9 0 6 4 8 D 5 MAXTOR
Native| Translation
------+-----+-----+-----
Form 3.5"/SLIMLINE Cylinders |12555| |
Capacity form/unform 6480/ MB Heads | 16| |
Seek time / track 9.0/ 1.0 ms Sector/track | 63| |
Controller IDE / ATA4 ULTRA Precompensation
Cache/Buffer 256 KB MAXCACHE Landing Zone
Data transfer rate 15.200 MB/S int Bytes/Sector 512
33.000 MB/S ext UDMA
Recording method PRML operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 5 55 | -40 71
Power: sleep 0.8 W Humidity % 5 95 | 5 95
standby 1.3 W Altitude km -0.061 3.048| -0.061 12.192
idle 4.1 W Shock g 20 | 200
seek 9.0 W Rotation RPM 5400
read/write 4.3 W Acoustic dBA 36
spin-up 20.2 W ECC Bit SMART
MTBF h 500000
Warranty Month 36
Lift/Lock/Park YES Certificates EPA GREEN PC
**********************************************************************
L A Y O U T
**********************************************************************
MAXTOR DIAMOND MAX 3400
Pin 1
J1 IDE Connector | J2 Power
+----------- --------+-++-----------++---------+
| .................... || @ * * * || X X X X |
| .......... ......... || @ * * * * || X X X X |
+----------------------++-+-+-+-+-+-++-+-+-+-+-+
| | | | | | | | |
| | | | | | | | |
J50 Master/Slave -----+ | | | | | | | +-+12V
J48 Cable Select -------+ | | | | | +---+12V Return
J46 4092 Cyl Limitation---+ | | | +----- +5V Return
J44 Factory Reserved -------+ | +------- +5V
J42 Factory Reserved ---------+
**********************************************************************
J U M P E R S
**********************************************************************
MAXTOR DIAMOND MAX INSTALLATION SHEET
Jumper Setting
==============
+---+---+---+---+---+
|J50|J48|J46|J44|J42|
+-------------------------------------+---+---+---+---+---+
| Master/Slave | | | | | |
| Only Drive in single drive system* | J | | | | |
+-------------------------------------+---+---+---+---+---+
| Master in a dual drive system* | J | | | | |
+-------------------------------------+---+---+---+---+---+
| Slave in a dual drive system | O | | | | |
+-------------------------------------+---+---+---+---+---+
| Cable Select | | | | | |
| Disabled* | | O | | | |
+-------------------------------------+---+---+---+---+---+
| Enabled | | J | | | |
+-------------------------------------+---+---+---+---+---+
J=Jumpered O=Open *=Default
**********************************************************************
I N S T A L L
**********************************************************************
-ANY DIREC.
Notes on installation
=====================
Installation direction
----------------------
horizontally vertically
+-----------------+ +--+ +--+
| | | +-----+ +-----+ |
| | | | | | | |
+-+-----------------+-+ | | | | | |
+---------------------+ | | | | | |
| | | | | |
| | | | | |
+---------------------+ | +-----+ +-----+ |
+-+-----------------+-+ +--+ +--+
| |
| |
+-----------------+
The drive will operate in all axis (6 directions).
**********************************************************************
G E N E R A L
**********************************************************************
MAXTOR IDE INSTALLATION
INSTALLATION PROCEDURE FOR AN IDE DRIVE
---------------------------------------
1. Install a 40 pin Data Cable ensuring that pin 1, which can be
identified by the striped edge of the cable, is closest to the
power connector on the drive.
2. Install a DC power cable to the back of the drive.
3. Verify the jumper configurations for Master/Slave operation
(Note: Master will be the bootable drive. The slave will not
be bootable.) Also make sure the existing C: drive is jumped
to be the Master in a two drive system, not the only drive in
the system.
4. Apply power to the computer.
4a. When memory test is complete go into your system's Standard
CMOS set-up.
(Note: There are various ways to get into CMOS set-up, please
refer to system's manual for instructions.)
4b. If your system's BIOS supports a user programmable drive
type, program the BIOS with the default parameters of your
drive. If your system does not support a user programmable
drive type choose parameters that closely match but do not
exceed the drives MegaByte capacity. Escape from set-up
then choose write to CMOS and exit.
5. Boot from a DOS diskette that has FDISK.EXE and FORMAT.COM on
it. At the A> prompt type in FDISK. At the menu options select
option 1 to create a DOS partition. Another menu will appear
and from those options choose 1 to create a Primary DOS
partition. Select yes to make 1 large partition and it will
automatically become active. Then escape from FDISK.
6. At the A> prompt type in FORMAT C:/S This does a high-level
format on the drive and transfers the system files in order for
the drive to be bootable. (Note: IDE drives are low-level
formatted from the manufacturer and only need a high-level
format).
To configure the drive as a slave drive repeat steps 1-4 and
proceed with steps 5a. and 6a. as follows:
5a. At the C> prompt type in FDISK. When the menu options appear
select option 5 to switch to the second drive. Enter fixed
disk drive number 2. Then choose option 1 to create a DOS
partition, then select option 1 again to create a Primary DOS
partition or option 2 to create an Extended DOS partition.
(Note: C and D drives will always be the Primary partitions
but only the Primary partition on C: will have a status of
active).
6a. Proceed with a high-level format on the drive by typing FORMAT
D: (Note: Make sure the correct drive letter has been selected
for format).
7. The drive is now bootable. As a test remove the DOS diskette
from A and press reset to reboot the computer, a C> should be
displayed, the drive is now ready for operation.