2 1 0 5 A MICROPOLIS
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 3.5"/HH Cylinders 1760| 1024| |
Capacity form/unform 560/ 647 MB Heads 8| 16| |
Seek time / track 10.0/ 2.0 ms Sector/track | 63| |
Controller IDE / AT Precompensation
Cache/Buffer 512 KB READ-AHEAD Landing Zone
Data transfer rate MB/S int Bytes/Sector 512
5.000 MB/S ext
Recording method RLL operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 5 50 | -40 65
Power: sleep W Humidity % 10 90 | 10 95
standby W Altitude km -0.061 3.048| -3.050 15.240
idle W Shock g 5 | 60
seek 13.0 W Rotation RPM 5400
read/write 11.5 W Acoustic dBA 36
spin-up W ECC Bit 88,REED SOLOMON
MTBF h 300000
Warranty Month 60
Lift/Lock/Park YES Certificates
**********************************************************************
L A Y O U T
**********************************************************************
MICROPL. 2105A PRODUCT DESCRIPTION 135851 REV. A
+---------------------------------------------------------+
| |XX J2
| 1xx Power
| |XX
++ LED |XX
++ |XX
| |XX J1
| 1-+ |XX
| W1+-+J6 |XX
| W2+-+ |XX
| Reserved+-+ |XX
| Reserved+-+ |XX
| Reserved+-+ |XX
| |X1
| |
| |XX J3
| |XX Power
+----------------------------------xxxxxx-----------------+ 1
+--------------------------------------+
| ++J4 |
| ++ Frame Ground |
| |
| |
| |
| J2 J1 1 J3 |
+xxxxx1-XXXXXXXXXXXXXXXXXXXXXX-XXXXXXXX+
+Power--------Signal------------Power-1+
**********************************************************************
J U M P E R S
**********************************************************************
MICROPL. 2105A PRODUCT DESCRIPTION 135851 REV. A
Jumper Setting
==============
x = Jumper setting at factory
Master/Slave Selection
----------------------
The interface allows up to two drives (a Master and one Slave) to be
attached to the AT/IDE bus.
+----------------+-------------------------------------+
| Jumpers | |
| W2 W1 |Description |
+----------------+-------------------------------------+
| CLOSED OPEN |Drive is Master, Slave is present |
+----------------+-------------------------------------+
| OPEN CLOSED |Drive is Slave |
+----------------+-------------------------------------+
| OPEN OPEN |Drive is Master x |
+----------------+-------------------------------------+
Note:
The 2105A drive is configured on power-up to have 63 logical sectors
per track, 16 logical heads, and 1084 logical cylinders.
The capacity of the drive may exceed the capacity that the host
can access. This limitation stems from the communication link between
the DOS and the BIOS. A typical limit is 1024 cylinders, 16 heads,
and 63 sectors. For optimum use of the following options, the BIOS
may need to be modified.
Drive is Master, Slave is present:
Specifies the Master Drive (Drive 0) when two 2105A drives are used
in a system. The other drive is Slave.
Drive is Slave:
Specifies the Slave drive (Drive 1) when two 2105A drives are used in
a system. The other drive is Master.
Drive is Master:
Specifies the Master drive (Drive 0) when one 2105A drive is used in
a system.
J2 DC Power and pin connector assignments
-------------------------------------------
+---------+ pin 1 +5 V
| 1 2 3 | pin 2 +12 V
+---------+ pin 3 Return
J3 DC Power and pin connector assignments
-------------------------------------------
+------------+ pin 1 +12 V
| 1 2 3 4 | pin 2 +12 Return
+------------+ pin 3 + 5 Return
pin 4 + 5 V
**********************************************************************
I N S T A L L
**********************************************************************
MICROPL. 2105A PRODUCT DESCRIPTION 135851 REV. A
Notes on installation
=====================
Drive mounting
--------------
horizontally vertically
+-----------------+ +--+ +--+ +------------------+
| | | +-----+ +-----+ | | | x
| | | | | | | | x+----------------+x
+-+-----------------+-+ | | | | | | ||x x||
+---------------------+ | | | | | | || x x ||
| | | | | | || x x ||
x x | | | | | | || x x ||
+------x------x-------+ | +-----+ +-----+ | || xx ||
+-+------x--x-------+-+ +--+ +--+ || x x ||
| xx | || x x ||
| x x | || x x ||
+---x--------x----+ |x x|
x x x++----------------++x
Dimensions and Mounting
-----------------------
The 2105A drive uses industry-standard mounting for 3 -inch full-
height Winchester disk drives.
The drive is designed such that the outer frame should be hard
mounted to the host equipment; no additional/external shock mounts
should be used.
Recommended orientation is vertical on either side, or horizontal
with the Device Electronics board down; other mounting orientations
may be used provided the ambient air temperature around the drive is
kept at or below 50*C (122*F).
The term "ambient" becomes imprecise when referencing a drive in a
system, since it is difficult to determine where the air temperature
should be measured. To help resolve this confusion, Micropolis
specifies that the maximum HDA casting temperature (regardless of the
air temperature around the drive) is 60*C (140*F). Not exceeding this
temperature will ensure that the head-to-media interface never exceed
its temperature limit.
Mounting Screws
---------------
3 per side 6-32 UNC-2B thru
4 on bottom 6-32 UNC-2B thru
Caution: The mounting screws must be selected so that they do not
penetrate the bottom mounting holes by more than 0.20 inches or the
side mounting holes by more than 0.156 inches.
Screws that are too long will short to PCBA components and/or prevent
proper operation of the shock mount system and may damage the HDA.
Interface Electrical Characteristics
------------------------------------
Interface control, data, and status signals are TTL compatible in
both send and receive directions. Maximum cable length is 18 inches.
The following cable specification are provided to ensure system
integrity.
Driver IOL sink current = 12 milliamps (minimum)
Driver IOH source current is -400 microamps (maximum)
Cable capacitive loading = 200 picofarads (maximum)
Signal Connector J1
-------------------
J1 is a 40-pin connector. The bus interface connection is made via
this connector. Signals on J1 include the 16-bit data bus and control
and address lines.
Recommended Cable: 3M Scotchflex 3302-40 or equivalent.
Mating connector: 3M 3417-7000 or equivalent.
J2 DC Power Connector
----------------------
J2 is a 3-pin, keyed connector. Both +5V and +12V are supplied to the
drive via this connector. This power connector is usually used by
low-power computer systems.
Mating Connector: MOLEX 5480 or equivalent
J3 DC Power Connector
----------------------
J3 is a 4-pin, keyed, AMP MATE-N-LOCK connector. Both +5V and +12V
are supplied to the drive via this connector. This power connector
is the industry standard and is used in most applications.
Mating Connector: AMP 1-480424-0 or equivalent
Pins: AMP 350078-4
Suggested Wire Size: 18 AWG
Ground Connector J4
-------------------
3/16-inch spade lug J4 is provided for frame grounding. Systems
characteristics determine proper ground connection.
Mating connector: AMP 60972-2 or equivalent.
Adjustments and Maintenance
---------------------------
2105A drives require no adjustments or periodic maintenance;
additionally, no mechanical adjustments are required to prepare a
system for handling or shipment.
Field-Replacable Components
---------------------------
The concept of repair by replacement of complete functional
components is utilized in the 2105A, resulting in an MTTR of less
than 15 minutes.
**********************************************************************
F E A T U R E S
**********************************************************************
MICROPL. 2105A PRODUCT DESCRIPTION 135851 REV. A
The Micropolis 2105A high-performance, 3 -inch, full-height
Rigid Disk Drive provides OEMs with high-speed, random access data
storage and meet the needs of diverse applications environment.
The drive is compatible with the proposed ANSI ATA (AT Attachment)
specification.
How to Access Large Capacity IDE Disk Driver
--------------------------------------------
Many disk drive users think that the IDE interface cannot be used
with high capacity disk drives. This is absolutely not so!
The Disk Operating System (DOS) provides for the file system stored
in the disk drive. The application programs access the disk drives
by activating specific DOS interrupts. The DOS interrupt service
program activates the DOS disk drive device driver that services disk
access request. The DOS driver activates the BIOS interrupt 13H. The
BIOS program services disk access request by activating the disk
drive IDE interface commands.
The ONTRACK MANAGER utility software including the following
features:
a. Automated installation and setup
b. Driver software for single drive 1 GB operation
c. Read/Write multiple sector performance driver
Seek Time
---------
| 2105A |
----------------------------------+--------+
Track-to-Track read msec. typ. | 1.5 |
write msec. typ. | 2.5 |
Average msec. typ. | 10 |
msec. max. | 25 |
Latency msec. avg. | 5.56 |
----------------------------------+--------+